PenSeal

DuraSil S is a single component, water-based surface hardener based on sodium silicates. These silicates react with the calcium hydroxide within the concrete matrix to harden the concrete surface making the concrete surface dust free and easier to clean. DuraSil S also contains a sealer component to impart water repellency.

5 litre 15 litre 200 litre

Excellent penetration Environmentally friendly Allows trapped moisture to escape Suitable for external use Australian Made

In-situ concrete and masonry, stone and terrazzo.

In-situ concrete and masonry. Terrazzo concrete

5 litre 15 litre 200 litre

Excellent penetration Environmentally friendly Allows trapped moisture to escape Suitable for external use Extremely low tendency towards formation of white surface deposits due to densifier pooling Improves surface stain resistance Improves surface sheen and light reflectivity Australian Made

DuraShine is a single component, lithium silicate based densifier and polish. These silicates react with the calcium hydroxide within the concrete matrix to harden the concrete surface making the concrete surface dust free and easier to clean. The inclusion of organic polymer additives can assist in reducing the number of grinding steps required to produce a desired gloss finish.

Simple addition rates. Easy to use Australian Made

Diluent X is a diluent for use with solventfree epoxy and polyaspartic coating systems reducing the viscosity of those systems to in application.

EcoPoxy® solventfree epoxy systems. EcoDur polyaspartics

5 litre 20 litre 200 litre

Excellent penetration Environmentally friendly Allows trapped moisture to escape Suitable for external use Australian Made

DuraSil D is a single component, water based surface hardener based on sodium silicates. These silicates react with the calcium hydroxide within the concrete matrix to harden the concrete surface making the concrete surface dust free and easier to clean

In-situ concrete and masonry, stone and terrazzo.

5 litre 15 litre 200 litre

DuraSil L is a single component, water-based surface hardener based on lithium silicates. These silicates react with the calcium hydroxide within the concrete matrix to harden the concrete surface making the concrete surface dust free and easier to clean. Lithium based silicate densifiers show the lowest tendency towards the formation of white deposits on the surface from densifier pooling.

Excellent penetration Environmentally friendly Allows trapped moisture to escape Suitable for external use Extremely low tendency towards formation of white surface deposits due to densifier pooling Highest performance of alkali metal-based silicates Australian Made

In-situ concrete and masonry, stone and terrazzo.

5 litre 15 litre 200 litre

DuraSil P is a single component, water-based surface hardener based on potassium silicates. These silicates react with the calcium hydroxide within the concrete matrix to harden the concrete surface making the concrete surface dust free and easier to clean. An advantage of potassium silicates over sodium silicates is a reduced tendency for the formation of white deposits on the surface from densifier pooling.

Excellent penetration Environmentally friendly Allows trapped moisture to escape Suitable for external use Australian Made

In-situ concrete and masonry, stone and terrazzo.

5 litre 15 litre 200 litre

Simple addition rates. Environmentally friendly Low odour/non flammable Easy to use Australian Made

5 litre 15 litre 200 litre

EcoDur Waterborne Polyurethane coating systems. EcoPoxy Waterborne Epoxy coating systems. EcoCryl Waterborne acrylic coating systems.

Diluent W is a diluent for use with waterborne EcoDur and EcoPoxy coatings systems. The addition of Diluent W reduces the viscosity of coatings systems without sacrificing wetting, flow and levelling properties which would occur if straight water is used. Diluent W also contains an advanced defoamer system to minimise air bubbles forming on porous substrates.

1 litre 5 litre 20 litre 200 litre

PenSeal Ultra is a penetrating, invisible and breathable sealer designed to protect products such as tiles, pavers, exposed natural stone concrete and grout from damage due to water, salts and oil-based stains. PenSeal Ultra impregnates concrete to protect from ingress of salts, chlorides. It protects reinforced concrete from waterborne chloride ions making it an ideal protective surface treatment.

Maintains a natural look to the substrate. Repels stains, graffiti, and food products. Allows surfaces to breath. Penetrates porous surfaces. Prevents corrosion of reinforcement bars Repels water and oil-based stains. Minimizes efflorescence, alkali, silica reactions and freeze thaw problems. Suitable for indoor and outdoor (UV stable) Reduces mould and moss growth. Seals cracks up to 0.3mm reducing water ingress. Allows water vapour to escape from structure. Australian Made

In-situ concrete and masonry, stone and terrazzo.

4 litre 10 litre 20 litre 200 litre

Crystallisation resistant Convenient 2:1 by volume mix ratio with EcoPoxy® SF Resin. Nonflammable Negligible odour and toxicity Australian Made

EcoPoxy® TF is a two part solvent free epoxy resin system, for combining with selected fillers and aggregate to produce epoxy mortars of various consistencies. Ideal for bonding, sealing, priming, coating and grouting. May be used on vertical or horizontal applications as structural epoxy adhesive paste and filler.

Primers. Floor coatings. Coving applications. Epoxy screeds and mortars.

High flow properties Bonds to damp substrates. Rapid hardening and strength gain High chemical resistance. Pre-measured kits make ease of use. High tensile and compressive strength. 100% solids epoxy. Excellent adhesion to most substrates. Cures at temperatures down to 5°C. Negligible shrinkage. High mechanical strength. Solvent free.

Suitable for use on damp substrate. Grouting heavy duty supports beneath crane and transporter rails. Anchoring bolts, bars and fixings. Bonding new to old concrete. Adhesive promoter. Filling in holes, cavities. Repairing cracks in horizontal surfaces. Grouting off column bases As a high strength repair mortar when mixed with Ecopoxy Fillers As a protective coating for concrete and steel structures. Reinforcement bar primer. Corrosion protection on steel reinforcement prior to application of concrete repair mortar.

EcoPoxy® PG is a two part component, high performance, pre filled epoxy liquid, suitable for use as a pourable or trowellable grouting material and in bonding new to old concrete.

4 litre 10 litre 20 litre 200 litre

Crystallisation resistant Convenient 2:1 by volume mix ratio with EcoPoxy® SF Resin. Nonflammable Negligible odour and toxicity Australian Made

4 litre 10 litre 20 litre 200 litre

EcoPoxy® SF10 Hardener is a rapid cure hardener designed for use with EcoPoxy® SF Resin where Rapid Return To Service (RR2S) or applications in cold temperatures are required.

Primers. Floor coatings. Coving applications. Epoxy screeds and mortars.

Crystallisation resistant Convenient 2:1 by volume mix ratio with EcoPoxy® hardeners (Pourable grout system excluded). Nonflammable Negligible odour and toxicity Australian Made

4 litre 10 litre 20 litre 200 litre

Primers. Floor coatings. Coving applications. Epoxy screeds and mortars.

EcoPoxy® SF Resin is a custom blend of Bisphenol A and Bisphenol F epoxy resins, diluted in a monofunctional reactive diluent. This specific combination of epoxy resins and reactive diluents eliminates resin crystallisation on storage due to cold temperatures EcoPoxy® SF Resin forms the backbone of the Illawarra Coatings solventfree epoxy range. This range is based on our unique approach to solventfree epoxies that employs the Common Resin Principle (CRP). CRP allows the applicator to choose the appropriate curing agent for the task at hand. This approach not only minimises stock levels, but also eliminates the possibility of incorrect resin/hardener combinations. With a consistent 2:1 by volume mix ratio, hardeners can even be blended on site to fine tune properties depending on specific site conditions. For example, EcoPoxy® SF35 hardener can be blended with EcoPoxy® SF10 hardener in any ratio to reduce cure times.

EcoPoxy® MVB Ultra is a two-part waterborne epoxy coating system designed to act as a single coat moisture and vapour barrier primarily over rigid cementitious substrates.

In-situ concrete Brick, block, and stonework Fibre cement and AAC panels Precast and tilt up panels

Light grey

4 litre 10 litre 20 litre 30 litre 40 litre

Environmentally friendly Water cleanup Convenient equal part by volume mix ratio Nonflammable Negligible odour and toxicity Excellent adhesion to brick, masonry, concrete, compressed fibreboard, stone, and timber. Australian Made

4 litre 10 litre 20 litre 30 litre 40 litre

EcoPoxy® NPP is a high performance, two component, synthetic resin-based epoxy primer for non-porous surfaces providing a good bond coat prior to the application of subfloor levelling compounds and thin bed mortars. EcoPoxy® NPP is ideal on dense, smooth, non-porous substrates.

Light green

Dense, smooth, non-porous substrates. Ceramic tiles, dense concrete, metal surfaces, plastic, and most coatings

Environmentally friendly Water cleanup Convenient equal part by volume mix ratio Nonflammable Negligible odour and toxicity Excellent adhesion to brick, masonry, concrete, compressed fibreboard, stone, and timber. Australian Made

White Light grey

EcoPoxy® MVB is a two-part waterborne epoxy coating system designed to act as a moisture and vapour barrier primarily over rigid cementitious substrates.

4 litre 10 litre 20 litre 30 litre 40 litre

Environmentally friendly Water cleanup Convenient equal part by volume mix ratio Nonflammable Negligible odour and toxicity Excellent adhesion to brick, masonry, concrete, compressed fibreboard, stone, and timber. Potable water approved to AS4020 Australian Made

In-situ concrete Brick, block, and stonework Fibre cement and AAC panels Precast and tilt up panels

4 litre 10 litre 20 litre 30 litre 40 litre

Environmentally friendly Water cleanup Convenient equal part by volume mix ratio Nonflammable Negligible odour and toxicity Excellent adhesion to brick, masonry, concrete, compressed fibreboard, stone, and timber. Australian Made

Clear (transparent light yellow) White Australian Standard N35 - Light grey Other Australian Standard colours via colourpacks

EcoPoxy® WB is a high performance two component water based industrial epoxy coating system available in a range of colours and is designed for floor and wall applications where durability and chemical abrasion resistance is required.

In-situ concrete Brick, block, and stonework Fibre cement and AAC panels Precast and tilt up panels

EcoPoxy® SF35 is a high performance two component solventfree industrial epoxy coating system available in a range of colours. EcoPoxy® SF35 is designed for floor and wall applications where durability and chemical abrasion resistance is required.

Environmentally friendly. Convenient 2:1 by volume mixing. Nonflammable. High bond and adhesive strength. Negligible odour and toxicity. Excellent adhesion to brick, masonry, concrete, compressed fiberboard, stone, and timber. Australian made

In-situ concrete and masonry. Brick, block, and stonework. Compressed fiberboard, stone, and timber.

A range of Australian Standard AS2700 colours are available either by factory tint or colourpack.

4 litre 10 litre 20 litre 30 litre

Excellent adhesion Excellent resistance to marking and staining Exhibits excellent resistance to UV light Exhibits very good chemical resistance Can be used in areas subjected to high levels of pedestrian and vehicular traffic

6 litre 30 litre

Concrete and masonry.

A range of Australian Standard AS2700 colours are available by addition of colourpacks.

EcoPAS is a two component, high solids polyaspartic floor coating ideal for both internal and external concrete surfaces. EcoPAS has been specifically designed as a clear topcoat for Polished Concrete and as a UV stable topcoat for the Illawarra Coatings EcoFlake flooring system. EcoPAS has also be successively used over metallic epoxy floor systems.

Clear, non-staining liquid Reduces salt and water intrusion by up to 90% Penetrates into porous surfaces Prevents corrosion of reinforcement bars Prevents dampness inside buildings, prevents rising damp. Repels Water Able to minimise eliminates efflorescence, alkali, silica reactions and freeze thaw problems. Breathable, will not trap moisture, allowing water vapour to escape for the structure. Suitable for indoor and outdoor (UV stable)

In-situ concrete and masonry, stone and terrazzo.

1 litre 5 litre 20 litre 200 litre

PenSeal is a solventborne, water repellent, penetrating sealer designed to protect and treat masonry and cementitious structures for the prevention of water absorption. PenSeal impregnates concrete to protect ingress of salts, chlorides. It protects reinforced concrete from waterborne chloride ions making it an ideal protective surface treatment.

PenSeal WB is a ready to use waterborne mixture of silane, siloxane, and synthetic resins. It is used to impart water repellency to inorganic substrates such as mineral construction materials. In this respect, it differs from conventional (mono-functional) water-repellents. The pores of the substrate remain open, the water vapor diffusion is hardly affected, if at all.

1 litre 5 litre 15 litre 200 litre

In-situ concrete and masonry, stone and terrazzo.

Treatment of floors of natural or synthetic stone, or unglazed ceramic tiles for easy care. Treatment of windowsills and tabletops of natural or synthetic stone, or fibrous cement to avoid staining. Treatment of facades of natural or synthetic stone concrete or fibrous cement to allow easier removal of dirt, grease, graffiti, posters, etc, from monuments, exterior and interior walls. Water, and dirt repellent treatment of low-porosity natural stone, e. g. marble, travertine, and granite. Australian Made

In-situ concrete and masonry, stone and terrazzo.

Treatment of floors of natural or synthetic stone, or unglazed ceramic tiles for easy care. Treatment of window sills and table tops of natural or synthetic stone, or fibrous cement to avoid staining. Treatment of facades of natural or synthetic stone concrete or fibrous cement in order to allow easier removal of dirt, grease, graffiti, posters, etc, from monuments, exterior and interior walls. Water, oil and dirt repellent treatment of low-porosity natural stone, e. g. marble, travertine and granite. Australian Made

1 litre 5 litre 15 litre 200 litre

PenSeal Ultra WB is a ready to use waterborne mixture of silane, siloxane and synthetic resins. It is used in diluted form to impart both water repellency and oil repellency to inorganic substrates such as mineral construction materials. In this respect, it differs from conventional (mono-functional) water-repellents. The pores of the substrate remain open, the water vapor diffusion is hardly affected, if at all. Oil, grease, paint, etc. are easier to remove from surfaces that have been treated with PenSeal Ultra WB.

5 litre 15 litre 200 litre

Simple addition rates. Easy to use Australian Made

EcoPoxy® solventfree epoxy systems.

Diluent B is a diluent for use with solventfree epoxy coating systems specifically for highly filled systems, reducing the viscosity of those systems to aid in application.

Simple addition rates. Easy to use Australian Made

Diluent D is a diluent for use with solventfree polyaspartic coating systems, reducing the viscosity of those systems to aid in application. Diluent D is the preferred diluent for EcoPAS polyaspartics.

EcoPAS solventfree polyaspartic systems.

5 litre 15 litre 200 litre

Single component Environmentally friendly Low viscosity Good adhesion to concrete Cleaning and maintenance of surfaces is improved Improves surface stain resistance Improves surface sheen and light reflectivity Compatible with the DuraSil range of densifiers Australian Made

EcoGrout is a specially formulated grout and bonding agent. It is a single component product that reacts quickly with ground concrete dust to re-surface pinholes and divots created and exposed during the grinding process.

In-situ concrete and masonry. Terrazzo concrete

5 litre 15 litre 200 litre